Everything, every day, can be seen in the "wall surface". If the wall is not well done, it will not only affect the overall environment of the home, but also make the mood of the occupants very poor. From the environmental point of view, the wall from the blank to the completion of the renovation, the average wall per square meter will use 1-3 kg of various materials, if these materials are harmful to the standard, the consequences are unimaginable. Here are some questions about how to decorate the walls of the rough house . Follow the small series to find out! Blank house wall decoration step one: check the wall surface The wall in the rough room is generally a cement wall, so before the wall is decorated, it is necessary to carry out a detailed inspection of the wall. Thoroughly check whether the front of the cement that needs to be painted in the rough room is firm and flat. The plaster layer that spits on the wall is not strong enough or there are large gaps and voids. Xiaobian suggested that you can complain to the developer or the property, and ask for it to be redone. If the holes are repaired by yourself, it can be used to fill with plaster. However, if the flatness of the wall is poor (the error is greater than plus or minus 5mm), it should be considered to first grind to level. When checking the wall, you need to use horizontal lines to test whether the wall is level. If you don't maintain a certain level, you can ask the developer to redo. Blank room wall decoration step 2: finished product protection Before the wall is renovated, there should be other items to be done. When the wall is treated, it will inevitably have dust, and when the putty is put, there will be putty, paint or other glue drops, so in the right Before the wall is renovated, be sure to protect other finished products in the room. Generally, plastic paper of suitable size can be purchased in a convenience store, and the finished product to be protected is wrapped on the construction site, but the shielding strength of the finished product should be carefully guarded to avoid the possibility of damage to the finished product. Blank house wall decoration step three: preparation before scraping putty Before scraping the putty, make sure that the wall surface is firm and flat. The uneven surface can be cleaned with steel brush or other tools. The recessed area can be filled with cement to make the wall surface free of floating soil and floating. On the wall surface, the concrete interface agent (the individual wall surface may need to be patched), and the roller should be evenly distributed. After it is dried, the putty on the wall can be applied. Blank room wall decoration step four: scraping putty Before the putty on the wall in the rough room, the flatness of the wall should be measured. It can be measured with a measuring rule of two meters or more. This way, the method of scraping the putty can be determined. Generally, the putty on the wall needs to be scraped twice by putty, which can make the wall level and even the bottom color of the wall. If the flatness of the wall is poor, you can brush it a few more times. If the slope of the wall or wall with poor flatness is very large, you can consider first scraping the leveling gypsum for leveling, then after scraping the putty, the interval between the putty of each putty should be more than 2 hours (after drying) ). Rough wall decoration step 5: painting The paint includes two kinds of primer and top coat. First, the primer is applied, and the dust on the wall after the smoothing is cleaned, and the primer can be applied. The primer can be applied once and it must be uniform. After it has dried out, the next step can be carried out. The top coat is usually brushed twice, each time interval is 2-4 hours or more (subject to dry finish) is basically OK. After brushing the topcoat for the second time, it takes 1-2 days to completely dry out. Before the coating is completely dry, it must be waterproof, drought-proof, and sun-proof to prevent problems with the paint film. After the above steps are completed, the next step is to check the wall surface. The acceptance criteria are that the wall surface is flat, the yin and yang angles are vertical, no cracks, no holes, uniform color, and the paint film is full. After the step is completed. The above is just a case of various wall decoration, and does not represent all the wall decoration. The specific differences will be determined according to the difference between the decoration wall paint and the wallpaper. Other rough room decoration precautions 1. Plan and elevation drawings should be fully understood and professionally operated and designed. 2. Determine the size and type of appliances and appliances in your home for the next step. 3. How to carry out the renovation of the water circuit of the kitchen and bathroom and the place to be adjusted. 4, wood works should pay attention to the construction of the Veneer cleaning. 5, paint engineering, mixing paint should pay attention to the atomic ash can not be too thick, varnish and primer must be guaranteed to do a bit! 6. The laying of the floor should be smooth, the expansion joints should be kept well, and the floor should be laid in the lower part of the door pocket. 7, lamps and sanitary ware should be installed in a regular order, so as to avoid unnecessary trouble in the future. 8. The finishing work of various projects should be in place, not sloppy! In the construction process or later acceptance, we must do a good job of cleaning. The above is the whole content that Xiaobian brought to you about how to decorate the wall of the rough house. I believe that after reading this article, the small masters have a basic understanding of how to decorate the wall of the rough house, if you want to know more about the decoration. For enquiries, please click to enter the decoration process section. More related wonderful reading: What is the wall decoration step? What is the wall decoration step of the rough house?
Veneer Mdf board is mainly used for laminate floor, door sheet, partition, furniture, decoration of indoor&outdoor, office and home furniture, sould equipment, inside decoration of the car, antistatic floor of computer room, panel, security door, wall board etc, and also used for the package and the basic material of laminate Wood Flooring .
Veneer MDF Board is easily for coating finishing, every coating, oil paint are also on the surface of Veneer MDF, is the fist choice as the basic material of painting effects.Veneer MDF is one kind of beautiful material of decoration. Smooth and flat surface, fine texture, steady property. All kinds of venner, gummed paper, light metal plate, melamine paper etc, is also can on the surface of the Plain MDF . Plain MDF is made from acoustical board after drilling, is used in construction decorative progress, such as meeting room, displaying room, office etc. And we have Veneer UV MDF and Sapele Veneered MDF.
LULI Group Corp. Ltd, well known as the leading manufacturer for wooden, steel and paper products, located in Shouguang, Weifang, Shandong, China. Since the foundation in 1985, it focus on the production of Plywood , venner,MDF board, Particle Board, Door skin , Blockboard , Finger joint board, OSB, paper, Steel etc.
Veneer Mdf Details:
size:1220*2440MM 1830*3660MM 1830*2440MM 915&610*3660MM 1220*2800MM 1525*2440MM
THICKNESS:2MM-35MM
MATERIAL:POPLAR, COMBINE, PINE
GLUE:E0, E1, E2, FIRE-PROOF
CERTIFICATION:CARB, FSC, CE, SON CAP
Veneer Mdf Veneer Mdf,Veneer MDF Pegboard,Veneer UV MDF,Sapele Veneered MDF Luli Group Co.,Ltd. , https://www.plywoods.nl
